|
HP LASER PRINTER ERROR CODE
49. A COMMUNICATION OR CRITICAL FIRMWARE ERROR
If you need to down load a upgraded
version of firmware go her CLICK
HERE and
then click on the H.P. symbol and it will take to the right page on H.P.
web sight for software down loads.
HP LASER PRINTERS 1200, 2200,
3100 FAX, 3200 FAX, 4100
1. This is a communication error code with the application that is being used.
2. Go back to a different
software program and see if a job will print.
3. If message persists turn
printer off then on.
4. Disconnect the network
cable and then turn printer off then on.
5. If message still there when
the network cable is disconnected. Up grade firmware in jetdirect card and
the formatter board.
6. Bad network cable.
7. Bad jetdirect card.
8. Replace the firmware dimm.
9. Replace the formatter
board.
HP LASER PRINTER 2300
ERROR 49.XX 1.
A critical firmware error has occurred on the printer. 2.
Turn printer off then on. 3.
Disconnect the parallel cable or the network cable 4.
If message still there when the network cable is disconnected. Up
grade firmware in jetdirect card and the formatter board. 5. Bad network cable. 6.
Replace firmware dimm 7.
Replace the jetdirect card. 8.
Replace formatter board. 9.
Replace engine board.
HP LASER PRINTER 4200, 4300 1.
A critical firmware error has occurred on the printer. 2.
Turn printer off then on. 3.
Disconnect the parallel cable or the network cable 4.
If message still there when the network cable is disconnected. Up
grade firmware in jetdirect card and the formatter board. 5.
Replace firmware dimm 6.
Replace the jetdirect card. 7.
Replace formatter board. 8.
Replace engine board. HP
LASER PRINTER ERROR CODE 49.24.02 FOR THE PRINTERS 4200, 4300 ONLY 1.
The printer has experienced a critical error. 2.
Verify that the ribbon cables are fully seated in the connectors on
the D.C. controller. 3.
Replace the power supply. 4.
Replace D.C. controller. 5.
Replace the formatter board.
HP COLOR LASER PRINTER 4500
1. Indicates that a critical firmware error has
occurred. An invalid command or data was sent to the formatter causing
the processor to stop.
2. A poor-quality parallel
cable or network cable. 3.
Turn printer off then on. 4.
Disconnect the parallel cable and the network cable
5. If
message still there when the network cable is disconnected. Up grade
firmware in jetdirect card and the formatter board.
6. Replace firmware dimm
7. Replace jetdirect card.
8. Replace formatter board.
HP COLOR LASER PRINTER
4600, 5500
1. A
critical firmware error has occurred on the formatter.
2. Try a different software
application and see if the job prints. If the job prints the application
that you were using has a bad communications to the printer
3. Disconnect the parallel
cable or the network cable.
4. Turn printer off and remove
all dimms and EIO devices from the printer. Turn printer on and if the
error no longer exists, make sure the printer is off and back on as you
install each dimm and EIO device.
5. Download the up to date
firmware for the EIO / Network card and the formatter board. 6.
Replace the EIO / Network card.
7. Replace firmware dimm
8. Replace formatter board.
HP COLOR LASER PRINTER 8500
1.Indicates that a software or data communications error has occurred, or
corrupt data was sent to the printer. This can be caused during times of
high network traffic or incomplete or out-of-bounds print data. This error
can also occur because of defective EIO devices.
2. Communication error code. Turn printer off the back on.
3. Remove all EIO cards and
reinstall them to ensure they are seated correctly.
4. If using a parallel
connection, verify that the cable is IEEE-1284 compliant.
5. Replace the EIO/Network
card.
6. Replace the formatter
board.
HP LASER PRINTER 9000
1. Communication or critical firmware error occurred. Turn printer off the back on.
2. Up grade the firmware to
the latest version in the jetdirect card and the formatter board.
3. Replace firmware dimm
4. Replace jetdirect card and
formatter board.
|
